Cura 2 BETA now available for Delta Go!

Discussion in 'Software' started by Shai, Apr 7, 2017.

  1. Shai

    Shai Master printer guru Deltaprintr Staff

    Joined:
    Dec 25, 2013
    Messages:
    1,310
    Likes Received:
    289
    The Cura team has incorporated the Delta Go into the latest BETA release! Please download it and give it a try. If you find any issues, please report them here so we can fix it!

    Please note that certain settings like Z-hop haven't been set by default, so you will need to adjust it. Currently z-hop is set to 0 and retraction speed is set to 400mm/sec. You will need to change z-hop to 0.20 and enable it. As well as change retraction speed to 500mm/sec.

    Or you can adjust the settings to your liking. But please review all settings first. Some settings are hidden by default, so you will need to click the little gear icon next to each setting category.

    Download: http://software.ultimaker.com/ExternalNightly/
     
    Ben likes this.
  2. Matthias Peschek

    Matthias Peschek Active Member

    Joined:
    Nov 1, 2015
    Messages:
    282
    Likes Received:
    70
    Can you change the start/end gcode script as well as the dimensions? And the gcode flavour? (Would be nice to use it for the wooden one, too)
     
  3. Shai

    Shai Master printer guru Deltaprintr Staff

    Joined:
    Dec 25, 2013
    Messages:
    1,310
    Likes Received:
    289
    It already works with the wooden previous version since it's reprap. Everything can be edited.
     
    Matthias Peschek likes this.
  4. DJ Carter

    DJ Carter New Member

    Joined:
    Nov 13, 2016
    Messages:
    14
    Likes Received:
    1
    Hi there. Just got the Go upgrade and installed it (looks great!). Updated the firmware and downloaded Cura 2.6.1 for the Mac but don't see any way to run this command per instructions "play /sd/factory_setup.gcode ". The old one had a command line interface that I could submit gcode commands. How do I get around this?

    Thanks,
    DJ
     
  5. DJ T

    DJ T New Member

    Joined:
    Jul 31, 2017
    Messages:
    7
    Likes Received:
    1
    Cura 2 does the Delta GO need any changes with dimensions? I remember you mentioning the upgraded dimensions of the GO when we install the new extruder.

    Also Cura 2 now supports USB Printing same as Cura 1. Biggest difference and I have not been able to determine if it was removed or hidden is the fact when printing the pronterface interface no longer is visible when printing. (not an issue for me anyway since I moved to using octopi but maybe for others who relied on it in the past due to tech knowledge limitations or comfortability)
     
  6. Shai

    Shai Master printer guru Deltaprintr Staff

    Joined:
    Dec 25, 2013
    Messages:
    1,310
    Likes Received:
    289
    @DJ T Have you been able to print with the Delta Go using USB on Cura 2? As far as we're aware, it's not supported well enough to use on our printers. It may be that they have released an update we haven't been notified of yet.
     
  7. DJ T

    DJ T New Member

    Joined:
    Jul 31, 2017
    Messages:
    7
    Likes Received:
    1
    Prior to the carriage becoming cracked yes, I downloaded the latest version, in the bottom where it says Save to Gcode (i forget) YOu can drop it down to send to octoprint (currently using) or print on via USB. I will post photos later
     
  8. DJ T

    DJ T New Member

    Joined:
    Jul 31, 2017
    Messages:
    7
    Likes Received:
    1
    CURA 2.62
    upload_2017-8-1_18-52-29.png
     
  9. DJ T

    DJ T New Member

    Joined:
    Jul 31, 2017
    Messages:
    7
    Likes Received:
    1
    The only issue or at least I'm not sure if its a new thing but when printing I cannot find the pronterface window similiar to how CURA 1 did.
     
  10. Shai

    Shai Master printer guru Deltaprintr Staff

    Joined:
    Dec 25, 2013
    Messages:
    1,310
    Likes Received:
    289
    Have you been able to click print via usb and use it? (without octoprint) Because that feature currently does not work.
     
Loading...

Share This Page